Adding text in Tinkercad takes a few seconds: drag the Text shape onto the workplane and type your words. Getting text that looks good, prints cleanly and follows a curve takes a little more know-how. This guide covers all of it.
How to add text in Tinkercad
- Open a 3D design and make sure the shapes panel on the right shows Basic Shapes.
- Find the Text shape (it usually appears as a red “TEXT” block) and drag it onto the workplane.
- With the text selected, the shape inspector shows a text field. Delete the default word and type your own.
- Resize the text with the corner handles. Hold Shift while dragging to keep its proportions, and add Alt to scale from the center.
- Drag the text into position, or use the Align tool (L) to center it on another shape.
That’s how you “turn text into 3D text” in Tinkercad: the Text shape is already a 3D solid with height, so you don’t need a separate extrude step.
Text settings: font, height and bevel
The inspector for the Text shape typically includes:
- Font: a short list of built-in typefaces. The selection is limited; see the custom font section below.
- Height: how thick (tall) the letters are.
- Bevel and segments: these round off the top edges of the letters. A small bevel can make raised text look more finished, but large bevels can blur small letters.
You can also change the height simply by dragging the top white handle or typing a value into the height box.
Raised (embossed) vs engraved text
Raised text sits on top of a surface:
- Place the text so its bottom slightly sinks into the surface below it (by a fraction of a millimeter). That overlap ensures the letters fuse to the base.
- Select the text and the base, then Group (Ctrl + G).
Engraved text is cut into a surface:
- Select the text and switch it to Hole in the inspector (or press H).
- Lower it into the object so it cuts to the depth you want, for example 0.6–1 mm. Don’t push it all the way through unless you want a stencil.
- Select both and Group.
If you’re new to the solid/hole system, our guide to grouping objects and using holes in Tinkercad explains how it works.
How to put text on the bottom of a 3D print
Text on the underside of a print reads correctly only when you flip the part over, so the letters have to be mirrored in the design.
- Engrave (or raise) the text into the bottom face as above.
- Before grouping, mirror the text with the Mirror tool (M) along its left-right axis, so it reads backward from the top view. When the print is flipped over, it reads correctly.
- Engraved text on the bottom face generally prints better than raised text, since the part still sits flat on the build plate.
Shallow engraving on the first layers can look faint. Slightly deeper or wider letters usually help. See how to mirror and flip objects in Tinkercad for more on the Mirror tool.
How to curve text in Tinkercad
Option 1: a curved-text shape generator
Tinkercad’s shape library has included curved-text generators, often listed as something like “Curved Words.” Open the shapes panel, search for “curved” or “text,” or browse the shape generator categories. Once placed, these generators usually let you set:
- The text itself
- Point size (letter size)
- Arc angle (how far around the circle the text spreads)
- Radius
- Height (thickness)
Shape generators change over time, so names and parameters may differ from one version to the next. Our overview of Tinkercad shape generators explains where to find them.
Option 2: arrange individual letters around a circle
If you can’t find a generator, or want more control, build the arc by hand:
- Create each letter as its own Text shape.
- Place a reference cylinder or circle where the center of the arc should be.
- Position each letter on the circle’s edge and rotate it so it faces outward. If the letters are evenly spaced, the angle step is the arc you want divided by the number of gaps between letters. Typing exact angles helps here; see how to rotate objects by exact angles in Tinkercad.
- Delete the reference shape and group the letters.
This takes longer but works anywhere and gives you full control over spacing.
Wrapping text around a cylinder
Tinkercad has no “wrap onto surface” tool, so text on the side of a mug or cylinder takes a workaround:
- Use thin, individual letters placed around the cylinder and rotated to face outward (as in Option 2, but standing upright against the side).
- Let each letter sink a little into the cylinder so it fuses on grouping.
- For engraving, turn the letters into holes before grouping.
On small-diameter cylinders, flat letters won’t sit flush across their full width. Keeping letters narrow helps.
Using custom fonts
The built-in font list is short. Community-made custom-font text generators have accepted an SVG font file, and makers have used font-conversion tools to create one from a downloaded font. Availability has varied over the years, so search the shapes panel for “font” to see what’s currently offered.
Another reliable route is to type your text in a vector program such as Inkscape, convert it to paths, export it as SVG, and import that into Tinkercad. The SVG becomes a 3D shape you can scale and position. See importing images, PNG, STL and 3MF files into Tinkercad for how SVG import works. Check the font’s license if you plan to sell prints.
Tips for printable text
- Size: very small text tends to lose detail on FDM printers (see minimum feature size). Letters roughly 5 mm tall or more are a safer starting point, depending on your nozzle and font.
- Stroke width: bold, simple fonts survive printing better than thin or script fonts.
- Height: raised text of around 1 mm is usually clearly readable without being fragile.
- Overlap: always sink raised text slightly into the base so it doesn’t print as separate pieces.
- Test print: a small test tile with your font at a few sizes can save a failed final print.
For a practical project that uses text, see how to make a 3D printable keychain in Tinkercad.
Text vs the Note tool
If you only want a label or reminder in your workspace, not printable letters, use the Note tool instead of the Text shape. Notes appear as annotations in the editor and aren’t part of the exported 3D model. In many versions the Note tool sits near the Ruler, and our Tinkercad keyboard shortcuts page lists its hotkey.