Tinkercad

How to Design a Custom Cookie Cutter in Tinkercad

Design a 3D printable cookie cutter in Tinkercad from a basic shape or your own SVG drawing, with wall, rim and depth guidance and food-safety notes.

On this page
  1. What makes a good cookie cutter
  2. Method 1: from a basic shape
  3. Method 2: from your own drawing (SVG)
  4. Adding a stamp or embossed detail
  5. Printing tips
  6. A note on food safety

A custom cookie cutter is a classic Tinkercad project. It’s quick to design, fast to print, and fun to use. You can start from one of Tinkercad’s built-in shapes or turn your own drawing into a cutter. Dimensions below are typical starting points; adjust them for your dough and printer.

  • A thin cutting edge: around 0.8–1.2 mm, so it slices cleanly
  • Enough depth: roughly 12–20 mm tall, deeper than your rolled dough
  • A comfort rim: a wider, flat flange on top so it doesn’t dig into your hand
  • Simple outlines: very thin, sharp details tend to tear dough or stick

Method 1: from a basic shape

Make the cutting wall

  1. Drag a shape onto the workplane, such as the Heart or Star from Basic Shapes, or a cylinder for circles.
  2. Resize it to your cookie size, for example about 70 mm across, holding Shift to keep proportions.
  3. Set the height to about 15 mm.
  4. Duplicate it (Ctrl + D) and shrink the copy by about 2 mm in total on each horizontal dimension, which gives roughly a 1 mm wall. Hold Shift + Alt to shrink from the center, or type exact sizes.
  5. Make the copy slightly taller than the original so it cuts cleanly through the top, and set it to Hole.
  6. Select both, press L, click the original as reference, and center them on both horizontal axes.
  7. Group (Ctrl + G). You now have a thin outline wall.

Add a comfort rim

  1. Duplicate the original solid shape again (before hollowing), or rebuild it at the same size.
  2. Make it about 2 mm tall, and use a hole copy to leave a rim about 3–4 mm wide (shrink the hole copy by 6–8 mm total).
  3. Align it with the cutter, centered, and at the bottom of the wall on the workplane. The rim prints on the bed, and that end becomes the top you press on.
  4. Group the rim with the cutting wall.

When you use it, flip it over so the thin edge cuts and the wide rim is under your palm.

Why star points get thin

Shrinking a shape by a percentage doesn’t create an even wall. On a star or any shape with narrow points or deep inward curves, the scaled-down copy doesn’t sit evenly inside the original. The wall becomes thick in some places and thin or even broken in others, often at the tips. Fixes:

  • Use simple, rounded shapes with Method 1.
  • Check the wall all the way around before printing. Look straight down from the top view.
  • For complex shapes, use Method 2, which creates an even outline.

This is the same limitation described in how to hollow out an object in Tinkercad.

Method 2: from your own drawing (SVG)

Creating an outline in Inkscape

For a custom shape, such as a dinosaur, a logo silhouette or your child’s drawing:

  1. Draw or trace the silhouette as a single, solid filled shape. If you’re starting from a photo or scan, see importing images, PNG, STL and 3MF files into Tinkercad for tracing a PNG to SVG.
  2. In Inkscape, give the shape a stroke (outline) about 1 mm wide and remove the fill.
  3. Use Path > Stroke to Path so the outline becomes a solid shape of its own.
  4. Save as SVG.

Make a second version with a wider stroke, about 4 mm, for the rim, and save it as another SVG.

Importing and building the cutter

  1. In Tinkercad, click Import and choose the thin-outline SVG. Set the size so the cookie is the width you want.
  2. Set the outline’s height to about 15 mm.
  3. Import the wide-outline SVG at exactly the same scale, and set its height to about 2 mm.
  4. Align both centered, with both sitting on the workplane, and group them.

Because the stroke has an even width, the wall is even all the way around, even on sharp details. Some Tinkercad versions have also offered fill options for imported SVGs; check the inspector after import.

Adding a stamp or embossed detail

To press a pattern into the cookie, such as a face, initials or texture:

  • Add raised details inside the cutter that are shorter than the cutting wall, by about 3–5 mm, so they press into the dough without cutting through.
  • Connect each detail to the rim or wall so it doesn’t print as a loose piece.
  • Keep lines fairly thick, around 1.5 mm or more, so dough doesn’t stick in fine gaps.

Printing tips

  • Print with the rim side down on the bed. That way the cutter needs no supports.
  • Wall thickness should suit your nozzle. A 0.4 mm nozzle usually handles a 0.8–1.2 mm wall well, which is two or three lines wide.
  • Fast, low-infill settings are fine. A cookie cutter is mostly walls anyway.
  • Export as STL. See how to turn Tinkercad into an STL file.

A note on food safety

3D printed kitchen items need some caution:

  • Layer lines can trap food and bacteria. FDM prints have tiny grooves that are hard to clean thoroughly. This is the main concern with repeated use.
  • Material matters. Look for filament the manufacturer describes as food-contact safe. Even then, the printer’s nozzle, additives and colorants can affect whether the finished part is suitable, so a “food-safe” label on the spool isn’t a guarantee for the printed part.
  • Heat: PLA softens at fairly low temperatures, so hot water and dishwashers can warp it. Hand-wash in warm, not hot, water.
  • Practical precautions people take: keeping contact brief (cookie dough is cut and baked, which helps), wrapping the cutting edge in plastic film, treating printed cutters as short-lived and replacing them, or using the print as a pattern to bend a metal cutter.

If you’re making cutters for others, or to sell, be especially careful and check the guidance for food-contact materials where you live.

For more beginner projects, see how to make a 3D printable keychain in Tinkercad and our Tinkercad projects guide.

The complete guide to tinkercad

Tinkercad Tutorial: How to Design in 3D with Tinkercad
Read the guide

Keep exploring

Guides from other topics

All topics →