Tinkercad

How to divide objects in Tinkercad?

Tinkercad has no knife tool, but you can divide any object by duplicating it and cutting each copy with a Box hole. Precise cuts, pins and print prep included.

On this page
  1. The quick answer
  2. Step-by-step: cutting an object in half
  3. Placing the cut precisely
  4. Cutting into more than two pieces
  5. Angled cuts
  6. Adding alignment pins
  7. Preparing the halves for printing
  8. If you just want to separate grouped parts

The quick answer

Tinkercad doesn’t have a dedicated knife or slice tool. To divide an object, duplicate it, then use a Box set to Hole to cut away one half on the first copy and the other half on the second copy. Group each copy with its hole and you have two separate pieces.

Step-by-step: cutting an object in half

  1. Select the object and press Ctrl + D to duplicate it. The copy sits exactly on top of the original.
  2. Hide the copy for now with Ctrl + H. Hiding keeps it in the same position, which helps later.
  3. Drag a Box onto the workplane and set it to Hole.
  4. Size the hole so it’s larger than the object in every direction except where you’re cutting. It should completely cover one half.
  5. Position the hole so its edge sits exactly where you want the cut.
  6. Select the object and the hole and Group (Ctrl + G). Half A is done.
  7. Bring back the copy (Ctrl + Shift + H shows hidden shapes).
  8. Make a second hole covering the opposite half, with its edge at the same cut line, then group it with the copy. Half B is done.

A handy shortcut: before step 6, duplicate the hole, and move the duplicate by exactly its own width so it covers the other half. Set the duplicate aside (or hide it) until step 8. Then you have both cutters ready with a perfectly matching cut line.

Placing the cut precisely

The Align tool lines up matching points (edge to edge, or center to center), so a centered cut takes two steps:

  1. Make the hole exactly as wide as the object in the cutting direction, and larger in the other two directions.
  2. Select both, press L, click the object to make it the reference, and click the center dot on the cutting axis. The hole now overlaps the object exactly.
  3. Nudge the hole by half its width along that axis. Its edge now sits at the object’s center.

For a cut at a specific distance, drag the Ruler onto the workplane, select the hole, and type its position relative to the Ruler. See how to measure a dimension in Tinkercad.

Cutting into more than two pieces

Repeat the method for each piece. For a model cut into three slices, make three copies, and use two holes on the middle slice (one on each side). Keep each copy’s position unchanged until all the cuts are made, so the pieces line up.

Angled cuts

Rotate the hole box before grouping to make an angled cut. Type the angle for accuracy (see how to rotate objects by exact angles in Tinkercad). Use the same rotated position for both cutters so the faces match.

Adding alignment pins

When you divide a model to glue it back together, pins help the halves line up:

  1. After cutting, add a small solid cylinder (for example 4–5 mm diameter) to the cut face of one half, sticking out a few millimeters.
  2. On the other half, cut a matching socket with a slightly larger cylinder set to Hole, in the same position. A few tenths of a millimeter of extra diameter is a common starting point, depending on your printer. See 3D printing tolerances for more on fits.
  3. Make the socket a little deeper than the pin is long.

Another option is to cut sockets in both halves and print a separate dowel.

Preparing the halves for printing

  • Rotate each half so the flat cut face points down. That’s usually the best surface to print on.
  • Press D to drop it onto the workplane.
  • Export each half separately if needed (see how to turn Tinkercad into an STL file).

Splitting a large model this way is a common solution when it’s too big for your printer’s build plate.

If you just want to separate grouped parts

If your object is a Tinkercad group, you may not need to cut at all. Select it and press Ctrl + Shift + G to ungroup it into its original shapes. See grouping objects and using holes in Tinkercad. Imported STL files are different, because they can’t be ungrouped; see can I ungroup an imported STL file in Tinkercad?.

The complete guide to tinkercad

Tinkercad Tutorial: How to Design in 3D with Tinkercad
Read the guide

Keep exploring

Guides from other topics

All topics →