Tinkercad

How to Rotate Objects by Exact Angles in Tinkercad

Rotate shapes in Tinkercad by an exact number of degrees: use the rotation handles, type angles, snap while dragging, and control the pivot point.

On this page
  1. The quick answer
  2. The three rotation handles
  3. Typing an exact angle
  4. Snapping while dragging
  5. What point does Tinkercad rotate around?
  6. Rotating by the same angle repeatedly
  7. Laying a part flat after rotating
  8. Common problems

The quick answer

Select the shape and hover over one of the curved arrow handles around it. Click and start dragging, and an angle readout appears. Click the angle value and type the exact number of degrees you want, then press Enter. Use the handle for the axis you want to turn around.

The three rotation handles

When you select a shape, curved double-headed arrows appear around it:

  • The arrow around the base: rotates the shape around the vertical (Z) axis, spinning it like a turntable.
  • The two arrows on the sides: rotate it around the two horizontal axes, tipping it forward or back and tilting it left or right.

Hover over each arrow to see the rotation ring for that axis before you commit.

Typing an exact angle

  1. Select the shape.
  2. Click and hold a rotation arrow and start dragging slightly. A protractor-style ring and an angle value appear.
  3. Click the angle number to edit it, type the angle, for example 30 or -15, and press Enter.

The angle applies relative to the shape’s current orientation. Typing 30 twice rotates it 60° in total. Negative values rotate the other way.

The exact way the angle box appears can differ slightly between Tinkercad versions. If clicking while dragging doesn’t open it, try releasing the drag and clicking the number that’s displayed.

Snapping while dragging

When you drag a rotation handle without typing, Tinkercad snaps to set increments:

  • Keeping the cursor close to the shape, on the inner part of the ring, tends to snap in larger steps.
  • Moving the cursor further out along the ring gives finer, one-degree control.
  • Holding Shift while rotating snaps to 45° increments.

Watch the angle readout as you drag. For anything that must be exact, typing the value is the most reliable method.

What point does Tinkercad rotate around?

Tinkercad rotates a selection around the center of its bounding box, the invisible box that encloses it. For a single symmetric shape, that’s its middle. For an asymmetric shape or a group, the center may not be where you expect.

Rotating around a different point

Tinkercad doesn’t let you set a custom pivot point directly. Workarounds:

  • Rotate then reposition: rotate the part, then move it back into place with the Align tool or Ruler.
  • Balance the bounding box: group your shape with a second shape positioned so the group’s center lands on the pivot you want. A mirrored copy on the opposite side works well, as described in how to duplicate in Tinkercad. Rotate the group, then ungroup.
  • Rotate several shapes together: selecting multiple shapes rotates them all around the center of the combined selection.

Rotating by the same angle repeatedly

To make a pattern of rotated copies, such as spokes, petals or a ring of holes:

  1. Select the shape and press Ctrl + D.
  2. Rotate the copy by a typed angle (for example 360 ÷ 8 = 45° for eight copies).
  3. Press Ctrl + D again. Tinkercad repeats the same rotation for each new copy.

For circles of objects around a center, combine this with the pivot trick above, or use an array shape generator; see Tinkercad shape generators.

Laying a part flat after rotating

After you rotate a part, it may end up floating above the workplane or partly below it. Press D to drop it back onto the workplane. When preparing a print, rotate parts so a large flat face sits on the bed, which also reduces the need for supports. The Workplane tool can also help when you want to add details to an angled face; see using the Workplane tool in Tinkercad.

Common problems

  • Rotation is off by a fraction of a degree: you dragged rather than typed. Undo (Ctrl + Z) and type the value.
  • The shape moved as well as rotated: it rotated around its bounding-box center. Re-align it afterward.
  • You can’t get back to the original angle: rotations are relative, so type the opposite value (for example -30 to undo 30), or use Undo.
  • You wanted a flip, not a rotation: use the Mirror tool. See how to mirror and flip objects in Tinkercad.

The complete guide to tinkercad

Tinkercad Tutorial: How to Design in 3D with Tinkercad
Read the guide

Keep exploring

Guides from other topics

All topics →