Tinkercad

How to Bevel and Chamfer Edges in Tinkercad

Tinkercad has no general fillet tool, but you can round, bevel and chamfer edges with shape settings, hole cutters and a few reliable workarounds.

On this page
  1. Does Tinkercad have a bevel or chamfer tool?
  2. Rounding all edges of a box: Radius and Steps
  3. Beveling cylinders and text
  4. How to chamfer a single edge with a hole
  5. How to round only the vertical corners
  6. How to round just the top edges
  7. Saving a reusable chamfer or fillet cutter
  8. Why edges matter for 3D printing

Tinkercad doesn’t have a general fillet or chamfer tool that lets you click an edge and round or angle it. You can still get clean rounded and beveled edges by using built-in shape settings and cutting edges away with holes. Here are the methods that work, from easiest to most flexible.

Does Tinkercad have a bevel or chamfer tool?

Not as a standalone tool. What it does have:

  • A Radius setting on the Box (and some other shapes) that rounds every edge at once
  • Bevel settings on the Cylinder and Text shapes that soften their top and bottom edges
  • The solid/hole system, which can cut any edge treatment you can model as a shape

If you need a fillet on any edge at any size, that’s a job for parametric CAD; see our Tinkercad alternatives. For most hobby parts, the methods below are enough.

Rounding all edges of a box: Radius and Steps

  1. Drag a Box onto the workplane.
  2. In the shape inspector, find Radius and increase it. All twelve edges round over evenly.
  3. Increase Steps to make the curve smoother (more segments). Low step counts give a faceted, beveled look.

A few things to know:

  • The radius applies to every edge. You can’t round some edges and not others with this setting alone.
  • The radius is limited by the box’s smallest dimension. A thin box can only take a small radius.
  • If you resize the box after rounding, the radius setting stays the same, but the result can look different on a much bigger or smaller box.

Beveling cylinders and text

  • Cylinder: the inspector usually offers Sides, Bevel and Segments. Bevel softens the top and bottom edges, and Segments controls how smooth the bevel is. More Sides makes the cylinder rounder.
  • Text: the Text shape has bevel and segment settings too, which round the tops of the letters. See how to add and curve text in Tinkercad.

Other shapes have their own parameters. Click a shape and look at what the inspector offers before reaching for a workaround.

How to chamfer a single edge with a hole

A chamfer is a flat, angled cut along an edge. The classic Tinkercad method uses a Roof or Wedge shape as a hole.

  1. Place your main object, for example a Box.
  2. Drag a Wedge (or Roof) onto the workplane. A wedge already has a 45° sloped face when its width and height are equal.
  3. Set the wedge to Hole.
  4. Rotate and position it so the sloped face runs along the edge you want to cut, with the solid part of the wedge outside your object. Make the wedge longer than the edge so it cuts cleanly at both ends.
  5. Use the Align tool (L) to line it up with the edge.
  6. Select the object and the wedge-hole, then Group (Ctrl + G).

Sizing the chamfer exactly

For a 45° chamfer that removes 2 mm from each face, make the wedge’s two short sides 2 mm and 2 mm, with its long side running the full length of the edge. Then align its corner exactly with the object’s edge. Typing dimensions into the size boxes is easier than dragging. Our guide to measuring dimensions in Tinkercad helps you check the result.

For a different angle, change the wedge’s proportions. A wedge 2 mm deep and 4 mm tall cuts a steeper chamfer.

How to round only the vertical corners

A common need is a box with rounded vertical corners but a flat top and bottom, like a phone case or a tray. Two methods work.

Method A: build from cylinders and boxes.

  1. Place four cylinders at the corners, each with a diameter of twice your corner radius.
  2. Fill between them with two overlapping boxes, one inset on the length and one on the width, so the outline is fully closed.
  3. Select all pieces and group them.

Method B: cut the corners with fillet cutters.

  1. Make a small Box the size of the corner radius (for example 3 × 3 mm, full height).
  2. Place a cylinder of 6 mm diameter (twice the radius) so it overlaps the box’s inner corner, set it to Hole, and group. You’re left with a small cutter shaped like a corner with a curved inside.
  3. Set that cutter to Hole and place it on one corner of your object. Duplicate and rotate it (90° each time) for the other corners.
  4. Group everything.

Method B is handy once you’ve made the cutter, because you can save it and reuse it.

How to round just the top edges

This is one of the harder edge treatments in Tinkercad. Two practical approaches:

  • Rounded box, flat bottom: give a box a Radius, make it a little taller than you need, then cut off the bottom with a Box set to Hole and group. The result has rounded top edges and rounded vertical corners, with a flat, sharp-edged base that sits well on a print bed. For many parts this is close enough.
  • Long fillet cutters: use the Method B cutter above, but stretch it to the full length of an edge and lay it on its side along each top edge. The corners where two cutters meet may need small touch-ups, so expect some trial and error.

Saving a reusable chamfer or fillet cutter

If you build a cutter you’ll use again, keep it:

  1. Select the cutter.
  2. Look for an option to create a custom shape in the shapes panel. In many versions this sits under Your Creations.
  3. Give it a name. It will then be available in your shapes panel in future designs.

The exact location of this option may vary between Tinkercad versions.

Why edges matter for 3D printing

  • Bottom edges: a small chamfer (around 0.4–1 mm) on edges touching the build plate can hide “elephant’s foot,” the slight bulge where the first layers squash out.
  • Overhangs: chamfers print more easily than rounded fillets on downward-facing edges, because a 45° slope usually needs no support.
  • Comfort: rounded edges on handles, enclosures and toys feel better and are less likely to have sharp points.
  • Strength: rounding internal corners can reduce stress concentrations in parts that flex.

For a broader look at printing with Tinkercad, see is Tinkercad good for 3D printing?.

The complete guide to tinkercad

Tinkercad Tutorial: How to Design in 3D with Tinkercad
Read the guide

Keep exploring

Guides from other topics

All topics →