A box with a lid is a great Tinkercad project. It’s genuinely useful and it teaches hollowing, alignment and clearance, the skills behind most functional prints. This guide builds a simple lift-off lid that drops onto the box, plus a sliding-lid alternative.
The dimensions below are examples. Change them for your needs, keeping the relationships between the numbers.
What you’ll make
- A box with an outer size of 60 × 40 × 30 mm, 2 mm walls and a 2 mm floor
- A lid 3 mm thick with a lip that fits inside the box opening, so it stays in place
Step 1: make the box
- Drag a Box onto the workplane. Set it to 60 × 40 × 30 mm by clicking the dimension values and typing.
- Duplicate it (Ctrl + D) and resize the copy to 56 × 36 mm (60 − 4 and 40 − 4, for 2 mm walls). Make it 30 mm tall or more.
- Set the copy to Hole.
- Raise the hole 2 mm to leave a floor. Make sure its top extends above the box so the top is fully open.
- Select both, press L, click the outer box to make it the reference, and click the center dots on both horizontal axes.
- Group (Ctrl + G).
You now have an open-top box. For more on this technique, see how to hollow out an object in Tinkercad.
Step 2: make a lift-off lid with a lip
The lid has two parts: a flat top plate that matches the box’s outside, and a smaller lip underneath that slots into the opening.
- Top plate: drag in a Box and make it 60 × 40 × 3 mm, the same footprint as the box.
- Lip: drag in another Box. The box opening is 56 × 36 mm. Make the lip a little smaller to leave clearance, for example 55.6 × 35.6 mm (0.2 mm clearance on each side), and 4 mm tall.
- Hollow the lip (optional but saves material): duplicate the lip, shrink the copy by 3 mm on each horizontal dimension (52.6 × 32.6 mm), set it to hole, center it, and group it with the lip. This leaves a 1.5 mm rim.
- Stack them: place the lip directly under the top plate (the lip on the workplane, the plate raised 4 mm so it sits on top of the lip), and center them with Align.
- Group the plate and lip.
Move the lid off to the side of the box on the workplane.
Getting the fit right (clearance)
3D printed parts usually come out slightly different from the design. Holes and openings tend to print a little small, and outer edges a little large. That’s why the lip is smaller than the opening.
- Starting point: about 0.2–0.3 mm of gap per side is a common starting point for a lid that lifts off easily on a well-tuned FDM printer.
- Too tight? Reduce the lip’s length and width by another 0.2 mm or so.
- Too loose? Increase them slightly, or add a small bump on the lip for a snap feel.
- Test first: print a thin test ring of just the box’s top edge and the lid’s lip before printing the full box. It’s faster and uses less filament.
The right clearance depends on your printer, nozzle, material and settings. Our guide to 3D printing tolerances goes deeper.
Alternative: a sliding lid
A sliding lid runs in grooves cut into the box walls, like a pencil case.
- Make the box as in Step 1, but with thicker walls, for example 3 mm, so there’s room for a groove.
- Cut the groove: make a thin box hole about 1.6 mm tall, wider than the inner opening but narrower than the box’s outer width, so it cuts about halfway into each side wall. Place it a couple of millimeters below the top edge. Make it run from the open end of the box to partway into the far end wall, so the lid is held on three sides and stops at the far end.
- Open the entry end: cut away the top of the end wall at the open end, down to the bottom of the groove, so the lid can slide in.
- Make the lid: a flat box slightly smaller than the groove, about 0.2–0.3 mm thinner than the groove height and a little narrower than the groove width.
Sliding lids are a little harder to get right, so a test print is especially useful. A small chamfer on the lid’s leading edge helps it start into the groove.
Optional details
- Rounded corners: give the outer box a Radius for a softer look, and give the hole a smaller radius to keep walls even. See how to bevel and chamfer edges in Tinkercad.
- Finger notch: cut a small cylinder hole into the top edge of the box so the lid is easier to lift.
- Label: engrave text into the lid. See how to add and curve text in Tinkercad.
- Dividers: add thin solid walls inside the box for compartments.
Preparing for printing
- Print the box upright, with its open top facing up.
- Print the lid upside down, with the flat top plate on the build plate and the lip facing up. That way, neither part needs supports.
- Export the box and lid as separate STL files (select one, then export selected shapes), or as one file if your slicer can split parts. See how to turn Tinkercad into an STL file.
Once you’ve made one box, the same skills carry over to enclosures, planters and organizers. See more ideas in our Tinkercad projects guide.