Designing for 3D Printing

Minimum Wall Thickness and Feature Size for 3D Printable Models

Minimum wall thickness and feature sizes for FDM, resin and SLS prints, why FDM walls should be multiples of your line width, and how to check models before printing.

On this page
  1. Short answer
  2. Wall thickness in your model vs walls in your slicer
  3. FDM: think in line widths
  4. Resin (SLA/MSLA) and SLS
  5. Starting values table
  6. Other minimum feature sizes
  7. Strength: minimum isn’t the same as strong enough
  8. Common modeling pitfalls
  9. How to check wall thickness before printing

Short answer

Minimum wall thickness depends mostly on the printing process:

  • FDM (filament): about 0.8 mm at the absolute minimum with a common 0.4 mm nozzle, which is two extrusion lines. 1.2–2 mm or more is a safer starting point for parts that get handled or carry load.
  • Resin (SLA/MSLA): walls well under 1 mm can print on small models, but around 1–2 mm is more robust for anything handled, and larger flat walls need more.
  • SLS / MJF (powder nylon, usually through a service): often around 0.7–1 mm minimum, but follow the service’s own design guide.

“Minimum” means printable, not strong. The thinnest wall your printer can make is rarely the wall your part should have.

Wall thickness in your model vs walls in your slicer

The word “walls” means two different things:

  • Model wall thickness is the physical thickness of the geometry you design: the side of a box, the shell of a vase, the arm of a clip.
  • Slicer walls (perimeters/shells) are the number of extrusion lines the slicer uses around the outside of each layer, with infill filling the space inside.

If your model’s wall is thinner than the slicer’s wall setting, the slicer simply fills it with as many lines as fit. If it’s thinner than one line, it may skip it entirely. This article is about the first meaning: how thick to design things.

FDM: think in line widths

On FDM printers, the smallest unit of a wall is one extrusion line, which is usually about the nozzle diameter or slightly wider. That leads to a few practical rules:

  • A wall thinner than one line width may not print at all, or prints as gaps.
  • Two line widths (about 0.8 mm with a 0.4 mm nozzle) is a common practical minimum for a wall that prints reliably.
  • Design walls as multiples of your line width where you can, for example 0.8, 1.2, 1.6 or 2.0 mm with a 0.4 mm nozzle. In-between values can leave small gaps or force awkward thin infill.
  • Changing nozzles changes the rules. A 0.6 mm nozzle needs thicker minimum walls. A 0.25 mm nozzle allows finer ones, at the cost of slower printing.

Modern slicers with variable line width, such as the Arachne wall generator in recent Cura and PrusaSlicer versions, vary extrusion width to fill odd-sized walls more cleanly. That makes in-between thicknesses less of a problem, but it can’t print features thinner than the nozzle can lay down.

Resin (SLA/MSLA) and SLS

Resin printers cure liquid photopolymer with light, layer by layer, and can resolve much finer detail than FDM. Very thin walls are possible on small features, but cured resin tends to be brittle, and thin walls can warp, crack during support removal, or deform during washing and curing. Larger walls need more thickness than small ones, because a big, thin, flat panel is especially prone to warping. Manufacturers publish minimums for their own machines and resins, and these vary.

SLS and MJF fuse nylon powder with a laser or fusing agent. The surrounding powder supports the part, so overhangs aren’t an issue, and the nylon is tough. Thin walls are possible, but services typically set minimums somewhere around 0.7–1 mm, depending on wall size and whether it’s supported. Always use the specific service’s guidelines.

Starting values table

These are conservative starting points for hobby and prototyping work. Your printer, material and part size will shift them.

Feature FDM (0.4 mm nozzle) Resin (SLA/MSLA) SLS / MJF
Minimum wall (printable) ~0.8 mm ~0.5 mm on small features ~0.7–1 mm
Practical wall for handled parts 1.2–2 mm+ ~1–2 mm ~1–2 mm
Pin / post diameter ~2–3 mm+ ~0.5–1 mm+ ~1 mm+
Embossed/engraved detail depth ~0.5–1 mm ~0.2–0.5 mm ~0.3–0.5 mm
Gap between separate parts ~0.3–0.5 mm ~0.2–0.5 mm ~0.5 mm+

Vendor guides sometimes quote smaller numbers than these, especially for resin. Those are achievable best cases on specific machines. The values above leave margin for typical home printers.

Other minimum feature sizes

Pins, posts and vertical wires

Thin vertical features are fragile on FDM, because each tiny layer has little time to cool and little area to bond. They wobble as the nozzle passes and snap easily. As a rough guide, posts under about 2 mm in diameter are delicate on FDM. Printing several at once (so each layer has time to cool), or adding small fillets at the base, helps. Resin handles much finer pins but they stay brittle.

Embossed and engraved detail, including text

  • Raised (embossed) detail must be wide enough to print. On FDM, aim for strokes at least about two line widths wide. A few layers of height is usually enough to see.
  • Engraved detail needs to be wide enough that the gap doesn’t close up. Engraving tends to stay crisp on top surfaces and get muddier on sides.
  • Text follows the same rules. Bold, sans-serif fonts survive best, and very small text (roughly under 5 mm tall on FDM) gets hard to read. Our guide to 3D text and logo software covers lettering in more detail.

Gaps and clearances

Two surfaces meant to stay separate, such as a hinge pin and its knuckle or a print-in-place mechanism, need a large enough gap that the printer doesn’t bridge or fuse them. See 3D printing tolerances for clearance values by type of fit.

Holes

Small holes print undersized on FDM, and very small vertical holes (around 1–2 mm) may close up partly or entirely. Model them slightly oversized, or drill them out after printing. Horizontal holes may need a teardrop shape to avoid drooping. See designing prints without supports.

Strength: minimum isn’t the same as strong enough

A 0.8 mm FDM wall prints, but it’s easy to crush, flex or crack. For parts that do work, consider:

  • Use more thickness where loads concentrate, such as around screw holes, at the base of clips and brackets, and at corners.
  • Use ribs to stiffen large thin panels instead of thickening the whole wall. It saves material and print time.
  • Avoid sudden thick-to-thin transitions. They concentrate stress and can cause uneven cooling and warping.
  • Fillet internal corners to reduce cracking.
  • Remember layer direction. FDM parts are weakest between layers. A thin wall loaded across its layer lines fails much sooner than one loaded along them.
  • Bosses for screws and inserts typically need generous wall thickness around the hole, often at least as thick as the hole’s diameter, so they don’t split.

Common modeling pitfalls

Zero-thickness surfaces from mesh modeling

In Blender and other mesh modelers, it’s easy to build a model out of single surfaces, such as a plane for a cape or a cloth, that look solid on screen but have no thickness at all. Slicers can’t print them, or print nonsense. Fixes:

  • Add a Solidify modifier in Blender to give surfaces real thickness, then apply it before export.
  • Run the 3D-Print Toolbox checks (non-manifold, thickness) before exporting.
  • Make sure separate parts are joined or at least closed, watertight shells.

CAD programs that model solids avoid this issue, which is one reason they suit functional parts. Our overview of 3D modeling software for 3D printing explains the difference between solid and mesh modeling.

Scaling models down

Scaling a model down shrinks its walls and details along with it. A building with 2 mm walls at full print size has 0.5 mm walls at 25% scale, below the printable minimum on FDM. The same goes for swords, spears, antennas and fingers on miniatures. Check thin features after scaling, and thicken them, or switch to resin for very small scales.

Hollowing resin prints

Hollowing large resin models saves resin and can reduce peel forces, but:

  • Leave a wall thick enough to be robust. Many users start around 1.5–2 mm or more for medium-size models and adjust from there.
  • Add drain holes near the lowest point (as printed) so uncured resin can escape, and a vent hole to prevent suction.
  • Never seal uncured liquid resin inside a hollow part. It can leak or crack the print over time.

How to check wall thickness before printing

  • Meshmixer: Analysis → Thickness highlights areas below a chosen value.
  • Blender: the 3D-Print Toolbox has a thickness check and flags thin faces.
  • CAD software: many programs have a wall-thickness or thickness-analysis tool. You can also measure critical walls directly.
  • Slicer preview: after slicing, scroll through the layer view. Thin walls show up as single lines, gaps, or missing features. Some slicers can show line widths in the preview. If a wall doesn’t appear in the preview, it won’t print.
  • Test print a section. For thin features that matter, print just that area first.

If you need to thicken walls on a model you didn’t design, our guide to STL editing software covers mesh tools that can offset or solidify surfaces.

The complete guide to designing for 3d printing

The Best 3D Modeling Software for 3D Printing
Read the guide

Keep exploring

Guides from other topics

All topics →