Short answer
For desktop FDM printers, a common starting point is to leave a gap of roughly 0.1–0.5 mm per side between mating parts, depending on how tight you want the fit:
- Press / interference fit: around 0–0.1 mm
- Snug, push-together fit: around 0.1–0.2 mm
- Sliding or rotating fit: around 0.2–0.3 mm
- Loose fit or print-in-place moving parts: around 0.3–0.5 mm
These are only starting points. Every printer, nozzle, material and slicer profile behaves a little differently, so the reliable approach is to print a quick tolerance test and tune from there.
For snap-fits, the clearance matters, but material, orientation and the shape of the flexing arm usually decide whether the part works or breaks.
Tolerance vs clearance
The two terms often get mixed up:
- Tolerance is how far a printed dimension may deviate from the design. It describes how accurate your printer is.
- Clearance is the gap you design deliberately between two parts so they fit together.
You choose clearance based on your printer’s real-world tolerance. A printer that reliably hits within ±0.1 mm can use tighter clearances than one that varies by ±0.3 mm.
Why printed parts don’t come out exactly to size
Common reasons FDM parts come out off-size:
- Extrusion width and squish. Outer walls bulge slightly, so outside dimensions often print a touch large.
- Holes print small. Inner walls bulge inward, and the slicer approximates circles with straight segments, so holes usually come out smaller than modeled. Small holes are affected the most.
- Elephant’s foot. The first few layers are squashed against the bed and flare outward, which makes the bottom of a part slightly larger. A small chamfer on bottom edges, or the slicer’s elephant-foot compensation, helps.
- Shrinkage. Plastics shrink as they cool, and some (ABS, ASA, nylon) shrink noticeably more than PLA.
- Orientation. A hole printed vertically (its axis along Z) is round. A hole printed horizontally can sag at the top and come out slightly oval. Our guide to support-free design explains the teardrop fix.
- Calibration. Under- or over-extrusion, belt tension and steps-per-mm settings all show up in dimensions.
Most slicers offer XY size compensation or separate hole and contour compensation settings. These can correct systematic errors, but get the basics (flow, extrusion) calibrated first.
Starting clearances by type of fit
| Fit type | Clearance per side (FDM, starting point) | Examples |
|---|---|---|
| Press / interference | ~0–0.1 mm | Pins pressed into holes, bearings held tight |
| Snug / friction | ~0.1–0.2 mm | Lids that stay on, push-fit covers |
| Sliding | ~0.2–0.3 mm | Drawers, sliding lids, guide rails |
| Rotating / loose | ~0.3–0.4 mm | Hinge pins, knobs on shafts |
| Print-in-place | ~0.3–0.5 mm | Hinges and joints printed already assembled |
“Per side” means the gap on each face. A 10 mm peg in a hole with 0.2 mm clearance per side needs a 10.4 mm hole. For round parts, it’s easiest to think in diameters: add twice the per-side clearance to the hole.
Print a tolerance test for your setup
The quickest way to find your printer’s numbers:
- Model a small plate with a row of holes, all for the same peg, but with clearances stepping up from 0 to 0.5 mm in 0.1 mm increments. Label each with embossed numbers.
- Model a matching peg. Or do the reverse: one hole and several pegs.
- Print both with the same material, nozzle, layer height and orientation you’ll use for the real part.
- Test which hole gives a press fit, which gives a snug fit, and which slides freely. Write the values down.
Many ready-made tolerance tests exist on model-sharing sites too. Redo the test when you change filament type or nozzle size.
Designing snap-fit parts
A snap-fit uses a flexible feature that deflects during assembly and springs back to lock. 3D printing makes snap-fits easy to include, but they’re also one of the most common things to break.
Cantilever snaps
The most common design is a flexible arm with a hook on the end that catches on a ledge or window in the mating part. Guidelines:
- Make the arm long relative to its thickness. A longer, thinner arm bends further before it stresses the plastic. Short, stubby arms crack.
- Taper the arm, thicker at the root and thinner at the tip, to spread the stress more evenly.
- Fillet the root. A sharp corner where the arm meets the body is where cracks start.
- Angle the hook’s lead-in (roughly 30–45°) so it slides in easily. Make the retaining face steep for a permanent lock, or angled for a removable one.
- Keep deflection modest. Design the hook depth so the arm only has to bend a small amount. Start small and increase it after testing.
- Clearance around the arm and hook still matters. Something like the snug-to-sliding range above is a reasonable starting point, so the arm doesn’t rub or jam.
Annular (pen-cap) snaps
A ring-shaped bump on one part snaps into a matching groove on the other, the way a pen cap does. These work on round parts, allow rotation once assembled, and get harder to remove the deeper the groove. Because the whole ring must stretch, they suit flexible materials better than stiff ones.
Material and orientation
- PLA is stiff and fairly brittle. It’s fine for snaps that deflect a little and won’t be cycled often, but it tends to crack under repeated flexing.
- PETG is tougher and more forgiving, and a good default for functional snaps.
- Nylon and similar tough materials work best for snaps that flex often, and they’re widely used in industrial printing for exactly this.
- TPU and other flexible filaments suit soft latches, but they can be too floppy to hold firmly.
Orientation matters a lot. A cantilever arm should be printed so it bends along its layers, lying flat on the bed, not so that layer lines run across the arm where it bends. An arm printed upright will often snap cleanly along a layer line the first time it flexes.
Other joints: press fits, print-in-place, threads and inserts
- Press fits. Design with very little or no clearance, and add a small chamfer on the leading edge to help the parts start. Crush ribs (small vertical ribs inside a hole that deform on assembly) give a firm, repeatable fit across slightly varying prints.
- Print-in-place mechanisms. Hinges and chain links printed already assembled need generous clearance, often 0.3–0.5 mm, and gaps that the slicer actually renders. Check the layer preview to confirm the parts aren’t fused.
- Printed threads. Larger, coarse threads print well. Fine threads are unreliable on FDM. Add clearance to threads just as with any other fit, and print them vertically.
- Heat-set inserts. For screws that will be tightened repeatedly, brass heat-set inserts pressed in with a soldering iron are much more durable than threading directly into plastic. Follow the insert maker’s recommended hole size.
- Captive nuts. Hexagonal pockets for standard nuts need a little clearance too, and can be bridged with the sacrificial-layer trick when printed horizontally.
Model clearances as parameters
In parametric CAD (Fusion, Onshape, FreeCAD and others), define clearance as a named variable, such as fit = 0.2, and use it in every mating dimension. If the first print is too tight, change one number and everything updates. OpenSCAD works the same way with variables at the top of the file. This one habit makes iterating on fitted parts far quicker. Our guide to 3D modeling software for 3D printing covers which tools support it.
If you’re adapting an STL from somewhere else, small fit adjustments are harder. See how to edit STL files.
Resin and SLS differences
- Resin (SLA/MSLA) printers are generally more precise in XY and can often use tighter clearances than FDM. But cured resin can be brittle, so snap-fits need tougher resins and gentle deflections. Parts also change slightly during washing and curing.
- SLS and MJF (powder-bed nylon, usually through a print service) produce tough, isotropic parts that suit snap-fits well. Service providers publish their own recommended clearances, which are a better guide than general rules.
Troubleshooting fits
| Symptom | Likely cause | Try |
|---|---|---|
| Parts won’t go together at all | Clearance too small, elephant’s foot, over-extrusion | Increase clearance; chamfer bottom edges; check flow |
| Fit is tight one way and loose the other | Horizontal vs vertical hole orientation | Reorient, or use teardrop holes |
| Snap arm breaks on first use | Brittle material, layers across the bend, sharp root | Switch to PETG/nylon; print the arm flat; add a root fillet; reduce deflection |
| Print-in-place parts fused | Clearance too small, or slicer merging gaps | Increase clearance; check the layer preview |
| Lid too loose | Clearance too large | Reduce clearance or add small friction ribs |
Fit problems are often linked to walls that are too thin to flex or too thin to hold an insert. Check those with our guide to minimum wall thickness and feature size.